Warming tips for cozy home heating
Guide

Unveiling the mystery: why is your whirlpool washer refusing to fill with water?

Rob is a seasoned home improvement writer with over 15 years of experience researching and recommending products for the home. Prior to starting Nurturing Homeaid, he wrote extensively for This Old House magazine and has been featured as a home expert on several TV and radio programs. An avid DIY-er,...

What To Know

  • Connect a hose to the water inlet valve and turn on the water supply.
  • If the water pressure is sufficient, the problem may lie with the water pressure switch.
  • Whether it’s a clogged valve, a faulty switch, or a damaged hose, understanding the underlying cause will empower you to fix the problem and restore your washer to its optimal performance.

If your Whirlpool washer is leaving you with a dry tub, it’s time to investigate the underlying cause. This comprehensive guide will delve into the potential reasons behind this frustrating issue and provide step-by-step solutions to get your washer back in action.

Clogged Water Inlet Valves

Check the Water Supply Valves

Start by verifying that the water supply valves behind the washer are fully open. If they’re partially closed, water flow will be restricted.

Clean the Inlet Valves

Over time, sediment and debris can accumulate in the water inlet valves, blocking water flow. Remove the hoses from the valves and use a small brush to clean out any obstructions.

Faulty Water Pressure Switch

Test the Water Pressure

Connect a hose to the water inlet valve and turn on the water supply. If water flows out freely, the water pressure is adequate. If there’s no water flow, the pressure may be too low.

Replace the Water Pressure Switch

If the water pressure is sufficient, the problem may lie with the water pressure switch. This switch detects water flow and signals the washer to fill. Replace the faulty switch with a new one.

Damaged Water Hoses

Inspect the Hoses

Thoroughly examine the water hoses for any cracks, kinks, or leaks. Damaged hoses can restrict water flow or prevent it altogether.

Replace Leaking Hoses

If you find any leaks or damage, replace the affected hose with a new one. Ensure the hoses are securely connected to both the washer and the water supply.

Faulty Control Board

Reset the Control Board

Sometimes, a simple reset of the control board can resolve the issue. Unplug the washer from the power outlet for a few minutes, then plug it back in.

Replace the Control Board

If resetting doesn’t help, the control board may be malfunctioning. This board controls the washer’s functions, including water filling. Replace the faulty board with a new one.

Clogged Drain Pump

Clear the Drain Pump

A clogged drain pump can prevent water from entering the tub. Disconnect the washer from the power supply and remove the drain pump. Clean out any debris or obstructions.

Faulty Door Switch

Check the Door Switch

The door switch ensures that the washer door is closed properly before filling with water. If the switch is faulty, the washer may not fill.

Replace the Door Switch

If the door switch is not functioning correctly, replace it with a new one. Ensure the door is properly aligned and closes securely.

Summary: Resolving Your Whirlpool Washer’s Water Woes

By following the steps outlined above, you can effectively troubleshoot and resolve the issue of your Whirlpool washer not filling with water. Whether it’s a clogged valve, a faulty switch, or a damaged hose, understanding the underlying cause will empower you to fix the problem and restore your washer to its optimal performance.

Top Questions Asked

Q: How can I prevent my Whirlpool washer‘s water inlet valves from clogging?
A: Regularly clean the water inlet valves by removing the hoses and brushing out any debris.

Q: What should I do if my Whirlpool washer is not draining properly?
A: Check the drain pump for clogs and remove any obstructions. If the problem persists, consider replacing the drain pump.

Q: How do I know if the control board on my Whirlpool washer is faulty?
A: If resetting the control board doesn‘t resolve the issue, it may be faulty. Symptoms include erratic behavior, flashing lights, or unresponsive buttons.

Was this page helpful?

Rob Sanders

Rob is a seasoned home improvement writer with over 15 years of experience researching and recommending products for the home. Prior to starting Nurturing Homeaid, he wrote extensively for This Old House magazine and has been featured as a home expert on several TV and radio programs. An avid DIY-er, Rob takes pride in testing out the latest tools and gadgets to see how they can make home projects easier. When it comes to heating systems, he's evaluated over 50 different furnace and boiler models over the years. Rob founded Nurturing Homeaid with his business partner Jim in 2020 to provide homeowners with genuine product recommendations they can trust. In his free time, Rob enjoys remodeling old homes with his family and traveling to visit architectural landmarks across the country. He holds a bachelor's degree in Journalism from Syracuse University.
Back to top button