Unstacking kenmore dryers made easy: a no-nonsense guide

Unstacking a Kenmore dryer is a relatively simple task that can be completed in a few minutes. However, it’s important to follow the correct steps to avoid damaging the dryer or injuring yourself.

Safety Precautions

Before you begin, make sure to take the following safety precautions:

• Unplug the dryer from the electrical outlet.
• Allow the dryer to cool completely.
• Wear gloves to protect your hands.

Materials You’ll Need

• Socket wrench or adjustable wrench
• Screwdriver

Step-by-Step Instructions

1. Remove the Rear Panel

• Locate the two screws on the back of the dryer that hold the rear panel in place.
• Remove the screws and carefully lift off the rear panel.

2. Disconnect the Gas Line (Gas Dryers Only)

• If your dryer is gas-powered, you will need to disconnect the gas line.
• Use a wrench to loosen the nut that connects the gas line to the dryer.
• Pull the gas line away from the dryer.

3. Disconnect the Electrical Wires

• Locate the electrical wires that connect the dryer to the power source.
• Use a screwdriver to loosen the screws that hold the wires in place.
• Pull the wires away from the dryer.

4. Remove the Top Washer

• If you have a stacked washer and dryer, you will need to remove the top washer.
• Locate the screws that hold the washer to the dryer.
• Remove the screws and carefully lift off the washer.

5. Unbolt the Dryer from the Stack

• Locate the four bolts that hold the dryer to the stack.
• Use a socket wrench or adjustable wrench to remove the bolts.

6. Carefully Lift the Dryer

• Once the dryer is unbolted, carefully lift it off the stack.
• Be sure to support the dryer with both hands.

7. Reassemble the Dryer

• Once the dryer is unstacked, you can reassemble it in its new location.
• Follow the steps in reverse order to reattach the rear panel, connect the gas line (gas dryers only), connect the electrical wires, and reinstall the top washer (if applicable).

Troubleshooting

Dryer Won’t Start After Unstacking

• Check that the dryer is plugged into the electrical outlet.
• Make sure that the rear panel is securely attached.
• Check that the electrical wires are properly connected.

Gas Leak After Unstacking

• If you smell gas after unstacking your dryer, turn off the gas supply immediately.
• Contact a qualified gas technician to repair the leak.

Tips for Unstacking a Kenmore Dryer

• Have a friend or family member assist you with the unstacking process.
• Use a dolly or furniture mover to transport the dryer.
• Be careful not to damage the dryer or the stack when unbolting it.
• If you are not comfortable unstacking the dryer yourself, contact a qualified appliance repair technician.

Unstacking Your Kenmore Dryer Safely and Easily

By following these steps, you can safely and easily unstack your Kenmore dryer. With a little planning and preparation, you can have your dryer up and running in its new location in no time.

Common Questions and Answers

Q: How do I know if my Kenmore dryer is stackable?

A: Most Kenmore dryers are stackable. Refer to your dryer’s owner’s manual to confirm.

Q: Do I need to disconnect the water supply when unstacking a washer and dryer?

A: No, you do not need to disconnect the water supply when unstacking a washer and dryer.

Q: Can I stack my Kenmore dryer on top of any washer?

A: No, Kenmore dryers are only compatible with Kenmore washers.

Q: How much does it cost to unstack a Kenmore dryer?

A: If you unstack the dryer yourself, there is no cost. If you hire a qualified appliance repair technician, the cost will vary depending on the technician’s rates.

Q: How long does it take to unstack a Kenmore dryer?

A: It should take no more than 30 minutes to unstack a Kenmore dryer.

Q: What should I do if I encounter any problems while unstacking my Kenmore dryer?

A: If you encounter any problems, refer to the troubleshooting section of this guide. If you are unable to resolve the problem, contact a qualified appliance repair technician.