Sos! maytag dishwasher lights blinking? don’t panic, here’s the solution

Experiencing blinking lights on your Maytag dishwasher can be frustrating, but don’t worry! Resetting your dishwasher is a simple process that can resolve most minor issues. Follow our comprehensive guide to learn how to reset Maytag dishwasher blinking lights and restore your appliance to its optimal working condition.

Understanding the Blinking Lights

Before resetting your dishwasher, it’s crucial to understand what the blinking lights indicate:

• 1 blink: Float switch may be activated due to excess water in the dishwasher.
• 2 blinks: Door latch is not closed properly.
• 3 blinks: Water temperature is too low.
• 4 blinks: Drain hose is clogged or kinked.
• 5 blinks: Water inlet valve is not functioning correctly.
• 6 blinks: Control board malfunction.
• 7 blinks: Heating element is not working.
• 8 blinks: Communication error between the control board and other components.

How to Reset Maytag Dishwasher Blinking Lights

Method 1: Power Cycle Reset

1. Unplug the dishwasher from the power outlet.
2. Wait for 60 seconds.
3. Plug the dishwasher back in.
4. Press the “Start/Cancel” button to resume the cycle.

Method 2: Manual Reset

1. Open the dishwasher door.
2. Locate the “Reset” button, usually on the control panel or near the bottom of the door.
3. Press and hold the “Reset” button for 5-10 seconds, or until the lights stop blinking.
4. Close the dishwasher door.

Method 3: Error Code Reset

1. Open the dishwasher door.
2. Press and hold the “Start/Cancel” button for 3 seconds.
3. Release the “Start/Cancel” button and press it again 2 more times.
4. The display will show an error code.
5. Write down the error code for troubleshooting purposes.
6. Press and hold the “Start/Cancel” button for 5 seconds to clear the error code.

Troubleshooting Common Blinking Light Issues

Float Switch Activation

1. Check for leaks or water accumulation in the dishwasher.
2. Clean the float switch located at the bottom of the dishwasher.

Door Latch Issues

1. Ensure the dishwasher door is properly closed and latched.
2. Inspect the door latch for damage or debris.

Water Temperature Problems

1. Check the water heater settings to ensure it’s providing hot water.
2. Clean the water inlet screen to remove any blockages.

Drain Hose Clogs

1. Disconnect the drain hose from the dishwasher.
2. Check for any blockages or kinks.
3. Clean the drain hose using a drain snake or baking soda and vinegar solution.

Water Inlet Valve Malfunctions

1. Turn off the water supply to the dishwasher.
2. Disconnect the water inlet hose and check for leaks or blockages.
3. Replace the water inlet valve if necessary.

Control Board Errors

1. Unplug the dishwasher for several minutes.
2. Contact a qualified appliance repair technician for assistance.

When to Call a Professional

If you’ve tried all the reset methods and your Maytag dishwasher is still blinking lights, it’s best to call a professional appliance repair technician. They can diagnose the underlying issue and perform necessary repairs to restore your dishwasher to proper functioning.

Key Points: Reclaiming Dishwasher Harmony

Resetting your Maytag dishwasher blinking lights is a straightforward process that can resolve most common issues. By following our step-by-step guide, you can quickly get your dishwasher back up and running. Remember to address any underlying problems promptly to prevent further damage or inconvenience.

Questions We Hear a Lot

Q: Why is my Maytag dishwasher blinking 1 light?

A: The float switch may be activated due to excess water in the dishwasher.

Q: How do I clear the error code on my Maytag dishwasher?

A: Press and hold the “Start/Cancel” button for 5 seconds after entering the error code mode.

Q: Can I reset my Maytag dishwasher without unplugging it?

A: No, unplugging the dishwasher is necessary to perform a power cycle reset.