Alert! lg dishwasher error code ae? follow these simple steps for resolution

LG dishwashers are known for their reliability and performance, but even they can occasionally encounter issues. Error code AE is a common problem that can prevent your dishwasher from operating correctly. This blog post will provide a comprehensive guide on how to reset LG dishwasher error code AE and get your appliance back up and running in no time.

Understanding Error Code AE

Error code AE on an LG dishwasher indicates a problem with the water supply. It can be caused by several factors, including:

• Clogged water inlet hose
• Faulty water inlet valve
• Low water pressure
• Malfunctioning water pressure switch

Resetting Error Code AE

Step 1: Check the Water Inlet Hose

Inspect the water inlet hose for any kinks, bends, or blockages. Clean the hose thoroughly and ensure that it is securely connected to both the dishwasher and the water supply faucet.

Step 2: Test the Water Inlet Valve

Locate the water inlet valve, which is typically located near the bottom of the dishwasher. Disconnect the hose from the valve and turn on the water supply. If water does not flow out of the valve, it may be faulty and needs to be replaced.

Step 3: Check Water Pressure

Ensure that the water pressure to your home is adequate. The dishwasher requires a minimum water pressure of 20 psi to operate correctly. You can use a water pressure gauge to measure the pressure at your kitchen sink.

Step 4: Reset the Dishwasher

Once you have addressed the potential causes of error code AE, you can reset the dishwasher to clear the error. Here are two methods:

• Power Reset: Unplug the dishwasher from the power outlet for 30 seconds, then plug it back in.
• Control Panel Reset: Locate the “Start/Reset” or “Cancel” button on the dishwasher’s control panel. Press and hold the button for 5-10 seconds, or until the dishwasher beeps or the display resets.

Troubleshooting Additional Issues

If resetting the dishwasher does not resolve the AE error code, there may be other underlying issues. Here are some additional troubleshooting steps:

• Check the Water Pressure Switch: The water pressure switch monitors the water pressure in the dishwasher. If it is faulty, it can send incorrect signals to the dishwasher, resulting in error code AE. Replace the switch if necessary.
• Inspect the Drain Hose: A kinked or clogged drain hose can prevent water from draining properly, leading to error code AE. Clean the hose and ensure that it is unobstructed.
• Test the Control Board: The control board is the brain of the dishwasher and controls all its functions. If the control board is malfunctioning, it may cause various errors, including error code AE. Contact a qualified technician to diagnose and repair the control board.

Takeaways: Resolving LG Dishwasher Error Code AE

By following the steps outlined in this guide, you can effectively reset LG dishwasher error code AE and restore your appliance to its optimal performance. If the error persists after troubleshooting, it is recommended to contact an authorized LG service technician for further assistance.

Popular Questions

Q: What is the most common cause of error code AE on an LG dishwasher?

A: Clogged water inlet hose or a faulty water inlet valve are the most common causes.

Q: How can I prevent error code AE from occurring?

A: Regularly clean the water inlet hose and inspect the water inlet valve for any signs of wear or damage.

Q: Can I reset the dishwasher without unplugging it from the power outlet?

A: Yes, you can reset the dishwasher by pressing and holding the “Start/Reset” or “Cancel” button on the control panel for 5-10 seconds.

Q: How long does it take to reset an LG dishwasher?

A: The reset process typically takes a few seconds to complete.

Q: What should I do if the error code AE reappears after resetting the dishwasher?

A: Contact an authorized LG service technician for further troubleshooting and repair.