How to restore your maytag washer’s flow: expert tips for pump replacement
What To Know
- Replacing a Maytag washer pump can be a daunting task, but with the right tools and instructions, it’s a job that most homeowners can tackle themselves.
- The pump is typically located at the bottom of the washer, behind the front panel.
- Replacing a Maytag washer pump is a straightforward task that can be completed in under an hour.
Replacing a Maytag washer pump can be a daunting task, but with the right tools and instructions, it’s a job that most homeowners can tackle themselves. This comprehensive guide will provide you with step-by-step instructions on how to replace the pump in your Maytag washer.
Tools and Materials You’ll Need
- New Maytag washer pump
- Screwdriver
- Pliers
- Bucket or container
- Towels or rags
- Gloves (optional)
Safety Precautions
Before you begin, it’s important to take the following safety precautions:
- Unplug the washer from the power outlet.
- Turn off the water supply to the washer.
- Wear gloves to protect your hands from sharp edges.
Step 1: Locate the Pump
The pump is typically located at the bottom of the washer, behind the front panel. To access the pump, you’ll need to remove the front panel.
Step 2: Remove the Front Panel
- Open the washer door and remove the two screws holding the front panel in place.
- Gently pull the front panel towards you and lift it off the washer.
Step 3: Locate the Pump Hoses
Once the front panel is removed, you’ll see the pump hoses. Disconnect the hoses from the pump by pulling them straight out.
Step 4: Remove the Pump Mounting Screws
Locate the screws holding the pump in place and remove them. There may be two or three screws, depending on the model of your washer.
Step 5: Disconnect the Electrical Wires
Disconnect the electrical wires from the pump. Note the position of the wires so you can reconnect them correctly later.
Step 6: Remove the Old Pump
Once the hoses, mounting screws, and electrical wires are disconnected, you can remove the old pump. Pull the pump straight out of the washer.
Step 7: Install the New Pump
Insert the new pump into the washer and align it with the mounting holes. Secure the pump with the mounting screws.
Step 8: Reconnect the Electrical Wires
Reconnect the electrical wires to the pump, making sure to match the wires to their original positions.
Step 9: Reconnect the Pump Hoses
Reconnect the pump hoses to the pump. Ensure that the hoses are properly seated and secure.
Step 10: Reinstall the Front Panel
Place the front panel back onto the washer and secure it with the screws.
Step 11: Test the Washer
Plug the washer back into the power outlet and turn on the water supply. Run a short cycle to test the new pump.
Troubleshooting Tips
If the washer doesn‘t drain properly after replacing the pump, check the following:
- Make sure the pump hoses are properly connected.
- Ensure that the pump is securely mounted.
- Inspect the electrical wires for any damage.
Wrapping Up
Replacing a Maytag washer pump is a straightforward task that can be completed in under an hour. By following these step-by-step instructions, you can save yourself the cost of a professional repair.
Frequently Asked Questions
Q: How do I know if my Maytag washer pump is faulty?
A: If your washer is not draining properly, making excessive noise, or leaking water, the pump may be faulty.
Q: How often should I replace my Maytag washer pump?
A: The lifespan of a Maytag washer pump varies, but it typically lasts for several years. If you notice any of the symptoms mentioned above, it’s time to consider replacing the pump.
Q: Can I use any washer pump in my Maytag washer?
A: No, you should use a washer pump that is specifically designed for your Maytag washer model.