Diy drain repair: learn how to make your speed queen washer flow freely
What To Know
- If the drain hose is clear, the next step is to check the drain pump.
- Can I use a wet/dry vacuum to clean the drain hose and drain pump.
- However, be sure to use the wet/dry vacuum in the wet mode, as the dry mode can damage the drain hose and drain pump.
If your Speed Queen washer is not draining properly, it can be a frustrating and inconvenient problem. Fortunately, unclogging the drain is often a relatively easy task that you can do yourself. In this blog post, we will provide a step-by-step guide on how to make a Speed Queen washer drain.
Gather Your Tools
Before you begin, you will need to gather the following tools:
- A bucket or large bowl
- A flashlight
- A screwdriver
- A pair of pliers
- A wet/dry vacuum (optional)
Safety First
Before you start working on your washer, unplug it from the power outlet and turn off the water supply. This will help to prevent any electrical shocks or water damage.
Step 1: Locate the Drain Hose
The drain hose is typically located at the back of the washer. It is a large, black hose that connects the washer to the drain pipe.
Step 2: Disconnect the Drain Hose
Use a screwdriver to loosen the clamp that is holding the drain hose in place. Once the clamp is loose, you can pull the drain hose off of the drain pipe.
Step 3: Inspect the Drain Hose
Once the drain hose is disconnected, inspect it for any clogs or blockages. If you see any debris, use your fingers or a pair of pliers to remove it.
Step 4: Check the Drain Pump
If the drain hose is clear, the next step is to check the drain pump. The drain pump is located at the bottom of the washer. It is a small, black pump that is responsible for pumping the water out of the washer.
Step 5: Clean the Drain Pump
To clean the drain pump, remove the screws that are holding it in place. Once the screws are removed, you can pull the drain pump out of the washer. Use a flashlight to inspect the inside of the drain pump for any clogs or blockages. If you see any debris, use your fingers or a pair of pliers to remove it.
Step 6: Reassemble the Washer
Once you have cleaned the drain pump, reassemble the washer in the reverse order of disassembly.
Step 7: Test the Washer
Plug the washer back into the power outlet and turn on the water supply. Run a test cycle to make sure that the washer is draining properly.
Troubleshooting Tips
If you are still having problems with your washer draining, here are a few troubleshooting tips:
- Check the drain pipe. Make sure that the drain pipe is not clogged or blocked.
- Check the water pressure. If the water pressure is too low, the washer will not be able to drain properly.
- Call a plumber. If you have tried all of the troubleshooting tips and your washer is still not draining, you may need to call a plumber.
Wrapping Up
Unclogging the drain of a Speed Queen washer is a relatively easy task that you can do yourself. By following the steps outlined in this guide, you can get your washer draining properly again in no time.
Information You Need to Know
Q: How often should I clean the drain hose and drain pump?
A: You should clean the drain hose and drain pump every few months, or more often if you notice that your washer is not draining properly.
Q: What are some signs that my drain hose or drain pump is clogged?
A: Some signs that your drain hose or drain pump is clogged include:
- The washer is not draining properly.
- The washer is making a loud noise when it is draining.
- The water is backing up into the washer.
Q: Can I use a wet/dry vacuum to clean the drain hose and drain pump?
A: Yes, you can use a wet/dry vacuum to clean the drain hose and drain pump. However, be sure to use the wet/dry vacuum in the wet mode, as the dry mode can damage the drain hose and drain pump.