Diy heating haven: install mr. heater vertical vent kits for a warm and efficient winter
What To Know
- Use the screws provided with the vent kit to secure the vent pipe to the wall.
- Slide the vent cap onto the end of the vent pipe and secure it with the screws provided.
- A vertical vent kit is designed to vent your heater vertically through a wall, while a horizontal vent kit is designed to vent your heater horizontally through a window or door.
Installing a Mr. Heater vertical vent kit is a relatively straightforward process that can be completed in a few hours. By following these simple steps, you can ensure that your vent kit is installed correctly and safely.
Tools and Materials You’ll Need
- Mr. Heater vertical vent kit
- Drill
- 1/2-inch drill bit
- Screwdriver
- Level
- Tape measure
- Caulk gun
- Caulk
- Safety glasses
Safety Precautions
Before you begin, be sure to take the following safety precautions:
- Wear safety glasses to protect your eyes from flying debris.
- Turn off the gas supply to your heater before starting work.
- Allow the heater to cool completely before touching it.
- Do not smoke or use open flames near the heater or vent kit.
Step-by-Step Instructions
Step 1: Determine the Vent Location
Choose a location for the vent that is at least 12 inches from any combustible materials. The vent should also be located at least 3 feet above the ground and 1 foot below the ceiling.
Step 2: Mark the Vent Location
Use a level to mark the location of the vent on the wall. The vent should be centered on the wall and level.
Step 3: Drill the Vent Hole
Use a 1/2-inch drill bit to drill a hole through the wall at the marked location. The hole should be slightly larger than the diameter of the vent pipe.
Step 4: Insert the Vent Pipe
Insert the vent pipe into the hole from the outside of the wall. The pipe should be long enough to extend at least 1 foot beyond the inside of the wall.
Step 5: Secure the Vent Pipe
Use the screws provided with the vent kit to secure the vent pipe to the wall. The screws should be tightened until the pipe is snug but not overtightened.
Step 6: Install the Vent Cap
Slide the vent cap onto the end of the vent pipe and secure it with the screws provided. The vent cap should be angled slightly downward to prevent water from entering the vent.
Step 7: Seal the Vent Hole
Apply a bead of caulk around the outside of the vent hole to seal it. The caulk will help to prevent drafts and leaks.
Troubleshooting
If you encounter any problems during the installation process, refer to the following troubleshooting tips:
- The vent pipe is too short. If the vent pipe is too short, you can purchase a longer pipe from a hardware store.
- The vent pipe is not level. If the vent pipe is not level, you can use a level to adjust it.
- The vent cap is not angled correctly. If the vent cap is not angled correctly, you can adjust it by loosening the screws and rotating it.
- There is a leak around the vent hole. If there is a leak around the vent hole, you can apply more caulk to seal it.
Recommendations
Installing a Mr. Heater vertical vent kit is a simple and straightforward process that can be completed in a few hours. By following these steps, you can ensure that your vent kit is installed correctly and safely.
Popular Questions
Q: What is the purpose of a vertical vent kit?
A: A vertical vent kit allows you to vent your heater vertically through a wall. This is necessary if you cannot vent your heater horizontally through a window or door.
Q: What is the difference between a vertical vent kit and a horizontal vent kit?
A: A vertical vent kit is designed to vent your heater vertically through a wall, while a horizontal vent kit is designed to vent your heater horizontally through a window or door.
Q: How long does it take to install a vertical vent kit?
A: It takes about 2-3 hours to install a vertical vent kit.