Unveiling the secrets: how to clean shark rocket vacuum with cord
What To Know
- Use a soft brush or a damp cloth to remove any remaining dirt or debris from the walls of the tank.
- Clean the brushroll housing with a soft brush or a damp cloth.
- Use a soft cloth dampened with a mild detergent solution to wipe down the exterior of the vacuum, including the handle, body, and power cord.
Maintaining a clean and efficient Shark Rocket vacuum with cord is crucial to ensure optimal performance and extend its lifespan. If you find your vacuum struggling to pick up dirt or emitting foul odors, it’s time to give it a thorough cleaning. In this comprehensive guide, we will provide you with step-by-step instructions on how to clean your Shark Rocket vacuum with cord effectively.
Unplug and Disassemble the Vacuum
Before starting the cleaning process, unplug your Shark Rocket vacuum from the power outlet. Then, disassemble the following components:
- Remove the dirt tank
- Detach the swivel steering and wheels
- Separate the brushroll housing from the vacuum body
Clean the Dirt Tank
Empty the contents of the dirt tank into a trash can. Use a soft brush or a damp cloth to remove any remaining dirt or debris from the walls of the tank. Ensure that the filter is in place before reattaching the dirt tank.
Clean the Swivel Steering and Wheels
Inspect the swivel steering and wheels for any hair or debris that may be wrapped around them. Use scissors to carefully cut away any tangled hair. Wipe down the wheels with a damp cloth to remove any dirt or dust.
Clean the Brushroll Housing
Remove the brushroll from the housing by pressing the release button. Use scissors to cut away any hair or debris wrapped around the brushroll. Clean the brushroll housing with a soft brush or a damp cloth. Reattach the brushroll and ensure that it rotates freely.
Clean the Filters
Your Shark Rocket vacuum has two filters: a pre-motor filter and a HEPA filter. Both filters should be cleaned regularly to maintain optimal suction power.
- Pre-Motor Filter: Rinse the pre-motor filter under cold running water until the water runs clear. Allow the filter to air dry completely before reinserting it.
- HEPA Filter: Gently tap the HEPA filter against a hard surface to remove any loose dirt or dust. If the filter is heavily soiled, you can rinse it under cold running water. Allow the filter to air dry completely before reinserting it.
Clean the Exterior
Use a soft cloth dampened with a mild detergent solution to wipe down the exterior of the vacuum, including the handle, body, and power cord. Avoid using harsh chemicals or abrasive cleaners that could damage the finish.
Reassemble the Vacuum
Once all the components are clean and dry, reassemble the vacuum by following these steps in reverse order:
- Attach the brushroll housing to the vacuum body
- Insert the swivel steering and wheels
- Place the dirt tank on the vacuum body
- Plug the vacuum into a power outlet
Troubleshooting Tips
If you encounter any issues while cleaning your Shark Rocket vacuum with cord, refer to the following troubleshooting tips:
- Brushroll not rotating: Ensure that the brushroll is properly inserted and that there is no hair or debris wrapped around it.
- Loss of suction: Check if the filters are clogged or dirty. Clean or replace the filters as needed.
- Foul odors: Clean the dirt tank and filters thoroughly. If the odors persist, contact Shark customer support.
Top Questions Asked
Q: How often should I clean my Shark Rocket vacuum with cord?
A: It is recommended to clean your vacuum every 3-6 months, depending on usage frequency.
Q: Can I use tap water to clean the filters?
A: Yes, you can use cold running tap water to clean both the pre-motor and HEPA filters.
Q: Where can I find replacement filters for my Shark Rocket vacuum?
A: You can purchase replacement filters from the Shark website, authorized retailers, or third-party online marketplaces.
Q: How do I reset my Shark Rocket vacuum?
A: To reset your Shark Rocket vacuum, press and hold the power button for 10-15 seconds.
Q: My Shark Rocket vacuum is not turning on. What could be the problem?
A: Check if the power cord is plugged in securely. Ensure that the battery is charged (if applicable) and that there are no clogs or blockages in the vacuum.